Edger Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Edger Parts
- Engine stops after a few seconds or minutes
- Will Not Start
- See more...
- Engine stops after a few seconds or minutes
- Will Not Start
- See more...
- Will Not Start
- See more...
Removed air intake and filter
Loosened and disconnected gas line to carburetor
Unscrewed carburetor and disconnected from throttle arm
Reversed process using new carburetor, O-ring and gasket Read more...
- Will Not Start
- See more...
- Will Not Start
- See more...
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Edger Brands
- Echo Edger
- Husqvarna Edger
- Kawasaki Edger
- MTD Edger
- Poulan Edger
- Shindaiwa Edger
- Troy-Bilt Edger
- Weed Eater Edger
Related Edger Parts
- Edger Bearings
- Edger Blades
- Edger Brackets and Flanges
- Edger Caps and Lids
- Edger Carburetors
- Edger Engines
- Edger Filters
- Edger Handles
- Edger Hardware
- Edger Hoses and Tubes
- Edger Knobs
- Edger Manuals and Literature
- Edger Seals and Gaskets
- Edger Spark Plugs
- Edger Springs and Shock Absorbers
- Edger Starters
- Edger Transmissions and Clutches
- Edger Wheels and Rollers
- Edger Wire Plugs and Connectors
Popular Edger Models
Below are the most popular Edger models we have. Enter your model number in the search box to find your model.
- 128LD 128 Ld - 952711969 (Us_can)
- 128LD 128 Ld - 952711953 (Us_lowes)
- 128LD 128 Ld - 20093100001-Current (Us_can)
- 970 Electric Edger
- 128CD 128 Cd - 952711952 (Us Only)
- 128CD 128 Cd - 952711968 (Us_can)
- 224L 224 L
- PE550 Gas Edger
- PE550 Gas Edger
- PE550 Gas Edger
- PE550 Gas Edger
- PE550 Gas Edger
- 123L 123 L
- UT13140 4-Cycle Lawn Edger
- PWLE0799 79cc 4-Cycle Lawn Edger
- 322L 322 L (20020100001-20150100000)
- 322L 322 L (19991000001-20000100000)
- 322L 322 L (20000100001-20020100000)
- 323L 323 L (20080900001-Current)
- 323L 323 L (20051800001-20061400000)