Ariens Parts

Your Price

$6.21

Ariens Bearing

★★★★★

3 Reviews

PartSelect Number PS9006914

Manufacturer Part Number 532009040

The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in question, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.

Installation Instructions

robert from EUREKA, CA

transaxle rotated forward on 2015 Husqvarna YT42DXLS

2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair.

HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.

HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.

HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.

HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.

HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.

HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...

Cap Axle Black 1 50 x 1 00 – Part Number: 532104757

Your Price

$3.99

Ariens Cap Axle Black 1 50 x 1 00

★★★★★

1 Review

PartSelect Number PS9007667

Manufacturer Part Number 532104757

This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of your lawn mower or garden tractor. Over time, your dust cap may become damaged or lost due to wear and tear. If this happens, dirt and debris can freely enter the axle and hub, causing damage. This is an easy repair to make and does not require any tools. Just look for the cap axle on the rim of the wheel to make your repair.

Installation Instructions

Anthony from OLIVEHILL, TN

Wheel bushings were bad

Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side. Read more...

Your Price

$4.99

Ariens Shear Bolt

PartSelect Number PS9002923

Manufacturer Part Number 51001500

This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, inspect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

Installation Instructions

Dennis from WESTFIELD, MA

Switch return spring broken

Removed panel, unsrew switch assy. Remove electric connector s, reverse process to reinstall Read more...

Your Price

$37.30

Ariens Friction Wheel

★★★★★

1 Review

PartSelect Number PS17016657

Manufacturer Part Number 09475300

The Friction Wheel is part of the clutch assembly, which helps to drive your unit. If broken from being worn down, you will have drivability problems and should replace the part. This part is metal with a rubber outer ring, and comes in white/black. Installation will require a wrench set, socket set, and pliers and is rated as "Medium" difficulty by customers. Refer to your make, model and diagram to check if this is the right part for you.

Fixes these symptoms

Drive system does not work
See more...

Ring Klip Number T5304-75 – Part Number: 812000029

Your Price

$3.99

Ariens Ring Klip Number T5304-75

★★★★★

1 Review

PartSelect Number PS9143890

Manufacturer Part Number 812000029

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

Installation Instructions

Anthony from OLIVEHILL, TN

Wheel bushings were bad

Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side. Read more...

Shear Bolt and Nut – Part Number: 52100100

Your Price

$3.99

Ariens Shear Bolt and Nut

PartSelect Number PS9000870

Manufacturer Part Number 52100100

This shear bolt and nut, also known as the shear bolt assembly, is sourced from the original manufacturer, and it is guaranteed to fit your snowblower. Each assembly includes one metal shear bolt and one metal nut, located at the connection point between the auger and gearbox/shaft. It is a safety mechanism designed to protect the snowblower auger from damage caused by sudden stops or excessive resistance. When the auger encounters a blockage or excessive load the shear bolt will break thereby preventing more severe damage to the gearbox. Once the bolt is sheared, it will need to be replaced. The bolt will also need to be replaced if it is bent or worn down, as a faulty shear bolt can result in damage to the auger, gearbox, and motor, as well as reduced equipment ability to throw snow, and increased safety risks. Use a socket or wrench to unthread the nut and remove the broken shear bolt. Align the new shear bolt with the mounting hole and secure it with the new nut. Note that this is a common repair and it is best to have several spare shear bolts and nuts on hand.

Bolt and Washer Assembly – Part Number: 532193003

Your Price

$8.71

Ariens Bolt and Washer Assembly

PartSelect Number PS9020856

Manufacturer Part Number 532193003

This manufacturer-approved bolt and washer assembly is for lawn tractors. Wear work gloves to protect your hands when installing this part.

Installation Instructions

Robert from WHITMAN, MA

the head blew a vaulve guide destoying push rods

about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS THE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine Read more...

Your Price

$8.27

Ariens Aluminum Push Rod

PartSelect Number PS9073139

Manufacturer Part Number 690982

This is a replacement push rod for your lawn tractor engine. It is made of aluminum and is the push rod used for the exhaust valve. Occasionally, the push rod in your engine can become damaged, and will need to be replaced before your engine runs at full capacity. This push rod is approximately 6 inches in length, and is an OEM part sourced directly from the manufacturer.

Washer 25/32 x 1-1/4 x 16 Ga. – Part Number: 532121749

Your Price

$3.99

Ariens Washer 25/32 x 1-1/4 x 16 Ga.

★★★★★

2 Reviews

PartSelect Number PS9008998

Manufacturer Part Number 532121749

This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number to confirm this is the washer you need for your equipment. This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.

Installation Instructions

Frederick from BINGHAMTON, NY

Front wheels, too much end play

Shimmed the wheels out on axle.. No more slop. Read more...