Official Electrolux Microwave Oven Combo Parts

Videos!

Main Terminal Block Kit – Part Number: 5304409888

Your Price

$9.37

Electrolux Microwave Oven Combo Main Terminal Block Kit

★★★★★

12 Reviews

PartSelect Number PS471605

Manufacturer Part Number 5304409888

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Installation Instructions

Timothy from Spring Valley, AL

Cord was not tightened enough by delivery crew.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful. Read more...

Videos!

Your Price

$152.88

Electrolux Microwave Oven Combo GLASS

★★★★★

8 Reviews

PartSelect Number PS11728351

Manufacturer Part Number 5304503232

This tempered glass is supplied by the original manufacturer and measures 20 inches by 13 inches. It is an inner door glass, designed for use in ranges/ovens and has several purposes which include providing heat insulation, acting as protective barrier, and providing an opening to monitor the cooking/heating process. Over time the glass can break or break from impact, thermal shock, or improper installation. If the glass is defective, it needs to be replaced promptly to avoid leaking, loss of insulation and potential harm to the user. Remove any fasteners or clips that secure the glass and carefully dispose of it. Position the new glass in the same position and secure it appropriately.

Installation Instructions

Mitch from Fernandina Beach, FL

Cracked oven door inner glass

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck! Read more...

Videos!

Inner Door Glass (middle) – Part Number: 316117502

Your Price

$89.64

Electrolux Microwave Oven Combo Inner Door Glass (middle)

PartSelect Number PS2378854

Manufacturer Part Number 316117502

Meat Probe Sensor – Part Number: 5304504202

Your Price

$89.24

Electrolux Microwave Oven Combo Meat Probe Sensor

★★★★★

2 Reviews

PartSelect Number PS11757868

Manufacturer Part Number 5304504202

This meat probe sensor is an authentic manufacturer replacement part for cooking appliances that have a built-in meat probe feature. It is plugged into the receptacle assembly for use inside the appliance. The sensor measures the internal temperature of meat during the cooking process and sends the readings to the control panel where they can be viewed in real time. This ensures that the food is cooked to your desired level of doneness. Over time the internal sensor components may become faulty or the probe can fail due to mechanical damage resulting in inaccurate temperature readings, and failure to communicate with the control panel. Follow the sensor cable to the insertion point in the oven cavity and disconnect the faulty sensor. Install the new sensor into the insertion point and reattach the connectors to complete the repair.

Installation Instructions

Tim from Chicago, IL

Timer would run but the microwave won't start

I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up. Read more...

Your Price

$45.04

Electrolux Microwave Oven Combo SWITCH

PartSelect Number PS8769124

Manufacturer Part Number 5304493153

The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capacitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..

Fixes these symptoms

No heat
Won’t turn on
See more...

Installation Instructions

john from PITTSFIELD, MA

Original Meat Probe insulation separated on the probe end

I searched the web for a replacement and Parts Select had a picture and part number for the exact same probe. I ordered the probe and it arrived very quickly. The problem was that the probe I received didn't match the picture as shown on the web site. Instead I received a probe that was a different color and the actual probe was about 2" shorter than the one I was replacing. I called customer service and was told that the probe I received was the new version that the older version was discontinued. If they had updated their pictures on the web site I would not have ordered the probe. Parts Select customer service did apologize for the issue and offered to have me return for a refund.

I will order from Parts Select but I will call first to verify that the item pictured is the actual item being shipped. Parts Select please update the part pictures to show the actual items being sold. Read more...

Videos!

Convection Fan Blade – Part Number: 318398302

Your Price

$19.39

Electrolux Microwave Oven Combo Convection Fan Blade

PartSelect Number PS3409337

Manufacturer Part Number 318398302

This convection fan blade is designed for use with various makes and models of range and oven and is sold as an individual part. Made of metal and measuring approximately 4.75-inches in diameter, this genuine OEM fan blade works with the convection motor to circulate and distribute heat evenly throughout the oven. If your oven is not getting hot enough or the heat is not circulating properly, or if the fan blade in your oven has become warped, damaged, or chipped, it needs to be replaced immediately. To replace the fan blade, disconnect your range from the power and locate the fan assembly. With the appropriate screwdriver and wrench, remove any assembly covers and the securing nut from the blade. Once the nut is removed, install the new blade and secure it and re-install the cover.

Your Price

$14.50

Electrolux Microwave Oven Combo INSULATION

PartSelect Number PS5574151

Manufacturer Part Number 318372016

Installation Instructions

John from Stevensville, MD

replacing the fan on a convection oven (fan was making a vibration noise)

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore. Read more...