GE Freezer Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular GE Freezer Parts
Your Price
$92.40
In Stock
General Electric Freezer Refrigerator Water Filter
PartSelect Number PS10063209
Manufacturer Part Number RPWFE
This NSF-certified water filter helps to improve the taste, quality, and health of your water by removing a number of contaminants including mercury, lead, and trace pharmaceuticals. The filter should be replaced every six month or after 300 gallons of water have been filtered. If you are unsure if your filter is due for replacement, another indicator is if the water flow from the dispenser has slowed down considerably. Replacing this part is a simple task that does not require any tools or shutting off the water or power supply to your fridge. Once the new filter has been installed, be sure to run at least two gallons of water through before consuming.
Fixes these symptoms
- Ice maker not making ice
- Not dispensing water
- See more...
Installation Instructions
Barbara from EDMONDS, WA
Replace old filter with new water filter.
Remove old filter by pulling and not twisting and insert new filter by pushing in place.
Read more...
Your Price
$88.89
In Stock
General Electric Freezer Refrigerator Water Filter
PartSelect Number PS16217433
Manufacturer Part Number XWFE
This water filter is found in the rear upper-right corner of the interior of the refrigerator. If your model has a replacement indicator light it will turn red to signal the need for a replacement. If your model does not have an indicator light, the filter cartridge should be replaced every six months or earlier if you notice a decrease in the flow of water from the dispenser.
The filter media is carbon black and reduces leads, some pharmaceuticals, and fifty other contaminates. It is 2 inches deep, 6 inches high, 2.25 inches wide and weighs approximately 1 lbs. When it comes time to replace the filter, first discard the old one by turning it to the left to remove. It will release itself when it has been turned far enough.
Installation instructions are quick and simple but can vary slightly depending on if it is a bottom-freezer, side-by-side or multi-door bottom-freezer model. Refer to the user instructions for you filter. Do not forget to reset the filter change indicator if applicable. In bottom-freezer and side-by-side models this is done by pressing and holding the RESET WATER FILTER bottom for three seconds. On a multi-door bottom-freezer model, press the button underneath the Confirm Filter Change message while the water is dispensing. On select models this reset is done automatically once a new filter is installed.
Installation Instructions
Cesar from ROYAL PLM BCH, FL
Your Price
$73.07
In Stock
General Electric Freezer Refrigerator Ice and Water Filter
Once I received the shipment, I placed the Cup Drive into position and used the flat edge of a knife to allow the Cup Drive to slide into the tight-fitting position necessary. After positioning into place, I placed the ice collection bin back into the freezer...turned the ice-maker back on...and waited for ice to be made. A day later, the ice maker had produced enough ice to test the ice maker's dispensing mechinism. The cup drive worked perfectly...and ice began to be dispensed. The dispensor has been working ever since.
I also replace the ice and water filter...another very easy task...of unscrewing the old and replacing with the new filter. After replacing the filter, I let the water dispensor run for 2 minutes to flush all air out the system. The water dispensor work perfectly. Read more...
PartSelect Number PS8746144
Manufacturer Part Number MWFP
This OEM ice and water filter fits side-by-side and bottom-freezer GE models. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This also may lead to your refrigerator not dispensing water or ice properly. Manufacturers recommend you change your filter every six months to ensure it properly filters impurities. Depending on the model, a red light might also indicate that the filter is due for a replacement. Note: As per the manufacturer, this is an updated water filter. If you have never installed the updated part or your old model was made by Culligan, you may need the adapter to install the filter. See related parts. This filter is located inside the refrigerators upper right corner. It is common for water to drip from the dispenser when being changed so place a cloth underneath before you begin this repair. To remove the filter, turn it to the left until it releases without pulling down. Fill the new filter with tap water to prepare it. Position the new filter into the holder taking note of the arrows. The arrow on the front should be facing out. Gently push up on the filter and turn it to the right to secure it. Do not over-tighten. To release air in the system run 1-1/2 gallons of water through it. If your model has a reset button, press and hold this for a few seconds to reset it.
Fixes these symptoms
- Fridge too warm
- Ice maker dispenses too little ice
- Ice maker not making ice
- See more...
Installation Instructions
Fred from River Ridge, LA
Ice Maker stopped dispensing ice through Ice Maker Dispensor.
After taking Ice Maker's ice collection container out, I noticed that the plastic cup drive was broken. I did a websearch for repair and replacement parts for our GE refrigerator. I found PartSelect website easy to navigate and find the replacement part necessary...and placed an order.Once I received the shipment, I placed the Cup Drive into position and used the flat edge of a knife to allow the Cup Drive to slide into the tight-fitting position necessary. After positioning into place, I placed the ice collection bin back into the freezer...turned the ice-maker back on...and waited for ice to be made. A day later, the ice maker had produced enough ice to test the ice maker's dispensing mechinism. The cup drive worked perfectly...and ice began to be dispensed. The dispensor has been working ever since.
I also replace the ice and water filter...another very easy task...of unscrewing the old and replacing with the new filter. After replacing the filter, I let the water dispensor run for 2 minutes to flush all air out the system. The water dispensor work perfectly. Read more...
Your Price
$74.43
In Stock
General Electric Freezer Evaporator Fan Motor
PartSelect Number PS12741350
Manufacturer Part Number WR60X31522
This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.
Fixes these symptoms
- Clicking sound
- Freezer section too warm
- Fridge and Freezer are too warm
- See more...
Installation Instructions
Luis from College Station, TX
Freezer Fan
I removed two srews from the back panel inside fthe reezer compartment and the two that hold the air manifold/baffle? and pulled the baffle out. Then, I removed the two srews that hold the front part of the fan bracket behind the baffle and the back panel came out easily. Two more screws and one quick connect plug attached to the fan and I was done with removal. Insallation was even quicker, I slid the original fan right off the old motor and slid it on the new motor's shaft. Piece of cake! Thanks Partselect.
Read more...
Your Price
$11.02
In Stock
General Electric Freezer Light Bulb - 40W
PartSelect Number PS217532
Manufacturer Part Number 40A15
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place. Depending on your appliance, there may be a guard or cover protecting the lightbulb, in which case you may require additional tools to remove the cover. We recommend disconnecting the power supply to your appliance before changing the lightbulb.
Installation Instructions
J. Douglas from Grass Valley, CA
Broken plastic parts
Cleaned the refrigerator as the old parts were removed. Installed new parts as the old parts were removed so as to easily identify the replacement parts. Very easy and wife was extremely happy after old plastic parts self destructed over a period of months and refrigerator was essentially unusable on the bottom two drawers.
Read more...
Your Price
$27.00
In Stock
General Electric Freezer Temperature Sensor
PartSelect Number PS304103
Manufacturer Part Number WR55X10025
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too cold, or not defrosting properly, then there may be a problem with your sensor. The temperature sensor can break from material fatigue or through normal use, and should be replaced. It is attached to the evaporator and control housing in your appliance. It measures approximately 1.25 inches long with 18 inch wire leads, and is constructed out of plastic. This part comes in white, beige. It includes the sensor, with wire leads.
Fixes these symptoms
- Doesn’t stop running
- Freezer not defrosting
- Freezer section too warm
- See more...
Installation Instructions
Gerald from San Clemente, CA
Fridge too warm, evaporator icing up
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
Read more...
Your Price
$13.21
In Stock
General Electric Freezer Evaporator Fan Grommet - Red
save money do it yourself..... Read more...
PartSelect Number PS963756
Manufacturer Part Number WR02X12008
If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut driver to complete this repair.
Fixes these symptoms
- Clicking sound
- Freezer section too warm
- Fridge too warm
- See more...
Installation Instructions
alex from rohnert park, CA
evaporator fan making lots of noise
the repair was really easy!!! took longer to put the little clip on the fan part than it was to install the whole moter and put everthing back togethersave money do it yourself..... Read more...
Your Price
$38.48
In Stock
General Electric Freezer Temperature Sensor
PartSelect Number PS10059162
Manufacturer Part Number WB21X22134
The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor. Before you make this repair remember to unplug your range from the power source, and turn off the gas shut off valve.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Peter from stamford, CT
Oven would go in to a F2 Error
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
Read more...
Your Price
$216.23
In Stock
General Electric Freezer Ice Maker
PartSelect Number PS1993870
Manufacturer Part Number WR30X10093
This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.
Fixes these symptoms
- Ice maker dispenses too little ice
- Ice maker dispenses too much ice
- Ice maker not making ice
- See more...
Installation Instructions
Michael from Bradenton, FL
ice maker not working properly and door seal worn
Two screws held the icemaker on. You do not even have to take them all the way out to remove the IM. Replacement of the water valve was just as easy except they (parts manufacturer) updated the flange nut with a compression fitting and it took me a minute looking at it before I realize what was going on. The door seal could not be easier, no tools just a few minutes of time
Read more...
Your Price
$8.56
In Stock
General Electric Freezer Light Switch
PartSelect Number PS8758429
Manufacturer Part Number WR23X10725
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the switch. The switch is spring loaded and is a generally closed type of switch meaning there should be no continuity when the button is depressed, and continuity through the switch when the button is not depressed. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat blade screwdriver and needle nose pliers.
Fixes these symptoms
- Fridge too warm
- Light not working
- See more...
Installation Instructions
Jonathan from Lilburn, GA
Sticking Light Switch
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
Read more...
General Electric Freezer Appliance Types
Related General Electric Freezer Parts
- General Electric Freezer Hardware
- General Electric Freezer Thermostats
- General Electric Freezer Switches
- General Electric Freezer Hinges
- General Electric Freezer Compressors
- General Electric Freezer Seals and Gaskets
- General Electric Freezer Brackets and Flanges
Popular General Electric Freezer Models
Below are the most popular General Electric Freezer models we have. Enter your model number in the search box to find your model.
