Hotpoint Ice Maker Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Hotpoint Ice Maker Parts
Your Price
$216.23
In Stock
Hotpoint Ice Maker
PartSelect Number PS1993870
Manufacturer Part Number WR30X10093
This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.
Fixes these symptoms
- Ice maker dispenses too little ice
- Ice maker dispenses too much ice
- Ice maker not making ice
- See more...
Installation Instructions
Michael from Bradenton, FL
ice maker not working properly and door seal worn
Two screws held the icemaker on. You do not even have to take them all the way out to remove the IM. Replacement of the water valve was just as easy except they (parts manufacturer) updated the flange nut with a compression fitting and it took me a minute looking at it before I realize what was going on. The door seal could not be easier, no tools just a few minutes of time
Read more...
Your Price
$67.70
In Stock
Hotpoint Ice Maker Single Outlet Valve Kit
PartSelect Number PS304375
Manufacturer Part Number WR57X10033
The water inlet valve on your refrigerator allows water to enter the ice maker and water dispenser. If your ice maker or water dispenser is not functioning properly, or you notice a leak, you may need to replace the single outlet valve. This single outlet valve has 1/4-inch compressions fittings and is intended for use with refrigerators that make crescent-shaped ice cubes. As per the manufacturer, this valve has a new quick connection. You must cut the retaining nut off your current plastic water line, and gently push it into the new valve. Be sure to disconnect the water and power sources from the refrigerator before you begin this repair.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- Leaking
- See more...
Installation Instructions
Michael from Bradenton, FL
ice maker not working properly and door seal worn
Two screws held the icemaker on. You do not even have to take them all the way out to remove the IM. Replacement of the water valve was just as easy except they (parts manufacturer) updated the flange nut with a compression fitting and it took me a minute looking at it before I realize what was going on. The door seal could not be easier, no tools just a few minutes of time
Read more...
Your Price
$29.33
In Stock
Hotpoint Ice Maker Ice Bucket - White
Without access to a friendly user website, I would have faced considerable delay in getting this part. Read more...
PartSelect Number PS3499784
Manufacturer Part Number WR30X10154
The ice bucket in your freezer collects the ice from the ice maker and stores it. If your old ice bucket is damaged you may want to replace it as it can leak. This product is made of white plastic and is approximately 13 inches in length and 9 inches wide at the widest point. This is an OEM part sourced directly from the manufacturer. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the damaged bucket, making sure to collect any broken pieces. Then, simply slide the new bucket in place.
Installation Instructions
Tom from Bradenton, FL
Ice bucket missing
I discovered the ice bucket missing from my rental unit at the beach. I was able to go online with my Blackberry, easily navigate your website using the model number to look up the part information , order it, and have it in place for the next renter. Without access to a friendly user website, I would have faced considerable delay in getting this part. Read more...
Your Price
$8.06
In Stock
Your Price
$8.06
In Stock
Hotpoint Ice Maker Water Tubing Clip
1. Turn off water supply.
2. Unplug power cord.
3. Remove bottom Panel to access the Solenoid valve.
4. Remove the water lines from the Valve.
5. Remove the Valve from the refrigerator.
6. Remove the electrical connectors from the valve.
(make sure the new valve has the connector adaptors included) you will need them during installation.
7.Bend the new valve bracket inward about 45 degrees to clear the compressor coolant line.
8.Use a pair of pliers to braek away the plastic on the new valve for clearance.
9.If needed remove the compression fitings from the old water line installation as the new valve comes with the push and lock feature.
10.Install the bottom 2 water lines they are different sizes
11.Mount the new valve to refrigerator and tighten.
12.Install the ice maker water line to the top fitting on the valve.
13.Plug the power cord in & turn on the water supply,check for leaks and proper operation on the valve. Read more...
PartSelect Number PS295031
Manufacturer Part Number WR1X5278
This water tubing clip, also known as a P-clamp, is usually used within refrigerators and freezers to organize the water line and tubing, but due to its versatility, this clip may also be used in other applications, like securing other cables. Made of metal and measuring approximately 1-inch in length, this clip features a hole on each side to allow you to screw it into the side of your appliance and secure the appropriate valve, tube, or cable. This clip is a genuine OEM part that is sold individually.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Louis from Kingwood, TX
Water leaking into Freezer from Ice Maker
Disregard previous.1. Turn off water supply.
2. Unplug power cord.
3. Remove bottom Panel to access the Solenoid valve.
4. Remove the water lines from the Valve.
5. Remove the Valve from the refrigerator.
6. Remove the electrical connectors from the valve.
(make sure the new valve has the connector adaptors included) you will need them during installation.
7.Bend the new valve bracket inward about 45 degrees to clear the compressor coolant line.
8.Use a pair of pliers to braek away the plastic on the new valve for clearance.
9.If needed remove the compression fitings from the old water line installation as the new valve comes with the push and lock feature.
10.Install the bottom 2 water lines they are different sizes
11.Mount the new valve to refrigerator and tighten.
12.Install the ice maker water line to the top fitting on the valve.
13.Plug the power cord in & turn on the water supply,check for leaks and proper operation on the valve. Read more...
Your Price
$24.87
In Stock
Hotpoint Ice Maker Water Line - 1/4"
PartSelect Number PS292409
Manufacturer Part Number WR17X1948
This water line 1/4, also known as a ice maker fill tube, is used in freezers and refrigerators. The tube directs the water into the ice maker cup during the cycle in which it fills the cup. The water line height is 0.6 inch and it weighs 0.1 lbs. As a safety precaution, unplug your appliance from the power source before installing this part. Remember to safely store food when it is removed from fridge or freezer. Refer to the installation instructions provided by the manufacturer for further guidance and accuracy.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
RUSSELL from BLACK HAWK, SD
water line cracked
I loosened the compression nut on the valve with my fingers and pulled the water line free from the valve. On the other end, I just pulled it from the hose clamp. Installation in reverse. Force the water line into the fitting on top, Slide the old nut over the line on the bottom. Screw the nut onto the valve. Reach inside the freezer and turn on the ice maker. Done. Before replacing the cardboard grill, you should vacuum the coils on the bottom, front and back. If practical, push it outside and blow it out with an air compressor or a leaf blower.
Read more...
Hotpoint Ice Maker Appliance Types
Popular Hotpoint Ice Maker Models
Below are the most popular Hotpoint Ice Maker models we have. Enter your model number in the search box to find your model.
