Hotpoint Refrigerator Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Hotpoint Refrigerator Parts
Your Price
$73.07
In Stock
Hotpoint Refrigerator Ice and Water Filter
Once I received the shipment, I placed the Cup Drive into position and used the flat edge of a knife to allow the Cup Drive to slide into the tight-fitting position necessary. After positioning into place, I placed the ice collection bin back into the freezer...turned the ice-maker back on...and waited for ice to be made. A day later, the ice maker had produced enough ice to test the ice maker's dispensing mechinism. The cup drive worked perfectly...and ice began to be dispensed. The dispensor has been working ever since.
I also replace the ice and water filter...another very easy task...of unscrewing the old and replacing with the new filter. After replacing the filter, I let the water dispensor run for 2 minutes to flush all air out the system. The water dispensor work perfectly. Read more...
PartSelect Number PS8746144
Manufacturer Part Number MWFP
This OEM ice and water filter fits side-by-side and bottom-freezer GE models. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This also may lead to your refrigerator not dispensing water or ice properly. Manufacturers recommend you change your filter every six months to ensure it properly filters impurities. Depending on the model, a red light might also indicate that the filter is due for a replacement. Note: As per the manufacturer, this is an updated water filter. If you have never installed the updated part or your old model was made by Culligan, you may need the adapter to install the filter. See related parts. This filter is located inside the refrigerators upper right corner. It is common for water to drip from the dispenser when being changed so place a cloth underneath before you begin this repair. To remove the filter, turn it to the left until it releases without pulling down. Fill the new filter with tap water to prepare it. Position the new filter into the holder taking note of the arrows. The arrow on the front should be facing out. Gently push up on the filter and turn it to the right to secure it. Do not over-tighten. To release air in the system run 1-1/2 gallons of water through it. If your model has a reset button, press and hold this for a few seconds to reset it.
Fixes these symptoms
- Fridge too warm
- Ice maker dispenses too little ice
- Ice maker not making ice
- See more...
Installation Instructions
Fred from River Ridge, LA
Ice Maker stopped dispensing ice through Ice Maker Dispensor.
After taking Ice Maker's ice collection container out, I noticed that the plastic cup drive was broken. I did a websearch for repair and replacement parts for our GE refrigerator. I found PartSelect website easy to navigate and find the replacement part necessary...and placed an order.Once I received the shipment, I placed the Cup Drive into position and used the flat edge of a knife to allow the Cup Drive to slide into the tight-fitting position necessary. After positioning into place, I placed the ice collection bin back into the freezer...turned the ice-maker back on...and waited for ice to be made. A day later, the ice maker had produced enough ice to test the ice maker's dispensing mechinism. The cup drive worked perfectly...and ice began to be dispensed. The dispensor has been working ever since.
I also replace the ice and water filter...another very easy task...of unscrewing the old and replacing with the new filter. After replacing the filter, I let the water dispensor run for 2 minutes to flush all air out the system. The water dispensor work perfectly. Read more...
Your Price
$74.43
In Stock
Hotpoint Refrigerator Evaporator Fan Motor
PartSelect Number PS12741350
Manufacturer Part Number WR60X31522
This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.
Fixes these symptoms
- Clicking sound
- Freezer section too warm
- Fridge and Freezer are too warm
- See more...
Installation Instructions
Luis from College Station, TX
Freezer Fan
I removed two srews from the back panel inside fthe reezer compartment and the two that hold the air manifold/baffle? and pulled the baffle out. Then, I removed the two srews that hold the front part of the fan bracket behind the baffle and the back panel came out easily. Two more screws and one quick connect plug attached to the fan and I was done with removal. Insallation was even quicker, I slid the original fan right off the old motor and slid it on the new motor's shaft. Piece of cake! Thanks Partselect.
Read more...
Your Price
$31.94
In Stock
Hotpoint Refrigerator Glass Shelf
PartSelect Number PS11699574
Manufacturer Part Number WR32X21260
Installation Instructions
Karen from COON RAPIDS, MN
Your Price
$21.27
In Stock
Hotpoint Refrigerator Module Shelf Insert - Clear
PartSelect Number PS2323438
Manufacturer Part Number WR71X10761
The Module Shelf Insert is a complete assembly for the module shelf. This repair is rated as "Easy" by users. Simply remove the old shelf insert and snap the new one into place using the locking tabs. This part is used to hold items in the fridge, and if broken it should be replaced. Refer to your user manual and model number to ensure this part is right for you.
Installation Instructions
Morgan from Acworth, GA
The clear plastic module shelf insert broke because I dropped it.
I popped out the old one and popped in the new one.
Read more...
Your Price
$11.02
In Stock
Hotpoint Refrigerator Light Bulb - 40W
PartSelect Number PS217532
Manufacturer Part Number 40A15
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place. Depending on your appliance, there may be a guard or cover protecting the lightbulb, in which case you may require additional tools to remove the cover. We recommend disconnecting the power supply to your appliance before changing the lightbulb.
Installation Instructions
J. Douglas from Grass Valley, CA
Broken plastic parts
Cleaned the refrigerator as the old parts were removed. Installed new parts as the old parts were removed so as to easily identify the replacement parts. Very easy and wife was extremely happy after old plastic parts self destructed over a period of months and refrigerator was essentially unusable on the bottom two drawers.
Read more...
Your Price
$27.00
In Stock
Hotpoint Refrigerator Temperature Sensor
PartSelect Number PS304103
Manufacturer Part Number WR55X10025
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too cold, or not defrosting properly, then there may be a problem with your sensor. The temperature sensor can break from material fatigue or through normal use, and should be replaced. It is attached to the evaporator and control housing in your appliance. It measures approximately 1.25 inches long with 18 inch wire leads, and is constructed out of plastic. This part comes in white, beige. It includes the sensor, with wire leads.
Fixes these symptoms
- Doesn’t stop running
- Freezer not defrosting
- Freezer section too warm
- See more...
Installation Instructions
Gerald from San Clemente, CA
Fridge too warm, evaporator icing up
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
Read more...
Your Price
$30.12
In Stock
Hotpoint Refrigerator Door Shelf Bar
PartSelect Number PS964507
Manufacturer Part Number WR17X11889
This door shelf is a replacement part for your refrigerator. It is very easy to install and requires no tools. Simply pull out the existing shelf bar and snap the new one into place, making sure the locking tabs are secure.
Installation Instructions
allan from brighton, MI
Your Price
$13.21
In Stock
Hotpoint Refrigerator Evaporator Fan Grommet - Red
save money do it yourself..... Read more...
PartSelect Number PS963756
Manufacturer Part Number WR02X12008
If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut driver to complete this repair.
Fixes these symptoms
- Clicking sound
- Freezer section too warm
- Fridge too warm
- See more...
Installation Instructions
alex from rohnert park, CA
evaporator fan making lots of noise
the repair was really easy!!! took longer to put the little clip on the fan part than it was to install the whole moter and put everthing back togethersave money do it yourself..... Read more...
Your Price
$93.82
In Stock
Hotpoint Refrigerator WATER VALVE WITH GUARD
PartSelect Number PS16226572
Manufacturer Part Number WR57X33326
This water inlet valve (Refrigerator Water Inlet Valve Assembly) supplies water to the ice maker and the water dispenser in your refrigerator. It is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. This part is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. Minerals and sediments can build up over time and cause a blockage in your inlet valve. They can also cause the valve to stick open, leading to an overflow of water. If this part is malfunctioning, water flow to your appliance could be compromised. Check for small ice cubes or a lack of ice cubes/water, as this is an obvious sign the part is damaged. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. Test your water inlet valve with a multimeter. You can test both the water dispenser side and the ice maker side. The part measures approximately 3 inches long and 2.75 inches wide and is constructed of plastic and metal. This replacement part features 1 dual inlet water valve with quick connections. It also has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- Leaking
- See more...
Installation Instructions
ralph from bristow, VA
Refrigertor water dispenser not working BUT ice machine is working
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and press the dispenser. If water comes out of the tube you have a frozen or blocked tube in the door. 2) Immediately adjust the temperature in the freezer and warm the freezer compartment as much as you can without destroying the freezer contents. Wait 24 hours. This will usually unfreeze the line. Do not waste your time with a hair dryer. NOW, if this doesn't work and you are convinced you need to order and replace the solenoid, follow these steps. Assemble your tools first. I needed a good ratchet set and a screwdriver. A shop towel is helpful for spilled water. A light is handy. Pull out the refreigerator to gain access to the rear of the unit. Unplug the power and close the water valve (older homes, you may need to actually shut the house water supply). Remove the screws which hold the cover over the lower half of the refrigerator. On the left you will see the solenoid. It's always good to see that your new part matches the one you feel needs replaced. They may not match perfectly due to changing design but they should be very similar. One screw holds this part in place and access is very simple. Now simply unplug the electrical connections. In my case, one blue "blade" type connection (powering the water) and one red "blade" type connection powering the ice maker. They are not the same size and this coupled with the coloring means you will not accidently switch them. pull the tubes clear of the solenoid. This is simple and needs no explantion. Grab your new solenoid and reattach both the electrical and water lines (two, remember, ice maker and drink dispencer). Replace the single screw. Re-attach the rear, lower refrigerator cover and go to the front of the unit to check the water. You can listen carefully and hear the power engage from the new part bringing you water. Clean up, replace the refrigerator back to its place and look really tired when your wife sees that you worked "so hard"! You probably saved at least $50-$80 from a service call which can now be used to take the family to dinner after your "exhausting" 15 minute workout of removing about 10 screws and wheeling the unit in and out of place. Writing this article took longer! My 4 year old worked harder holding the flash light!
Read more...
Your Price
$15.17
In Stock
Hotpoint Refrigerator Door Shelf Bar
PartSelect Number PS1015918
Manufacturer Part Number WR17X11890
This part is the door fixed shelf, also known as the door shelf bar, and it is built for your refrigerator. It allows food and beverages items to stay in the door shelf. It is made of white plastic. If your current door shelf bar is broken or missing, you will need to replace it. Many of our customers have rated this repair as easy. Simply lift out the old bar, and replace it with a new one. Be sure you can properly close your freezer door after the repair is complete.
Installation Instructions
Chris from E NORTHPORT, NY
Hotpoint Refrigerator Appliance Types
Related Hotpoint Refrigerator Parts
- Hotpoint Refrigerator Trays and Shelves
- Hotpoint Refrigerator Drawers and Glides
- Hotpoint Refrigerator Hardware
- Hotpoint Refrigerator Thermostats
- Hotpoint Refrigerator Seals and Gaskets
- Hotpoint Refrigerator Ice Makers
- Hotpoint Refrigerator Switches
- Hotpoint Refrigerator Dispensers
- Hotpoint Refrigerator Motors
- Hotpoint Refrigerator Doors
- Hotpoint Refrigerator Hinges
- Hotpoint Refrigerator Handles
- Hotpoint Refrigerator Door Shelves
- Hotpoint Refrigerator Elements and Burners
- Hotpoint Refrigerator Hoses and Tubes
- Hotpoint Refrigerator Valves
- Hotpoint Refrigerator Springs and Shock Absorbers
- Hotpoint Refrigerator Circuit Boards and Touch Pads
- Hotpoint Refrigerator Lights and Bulbs
- Hotpoint Refrigerator Compressors
- Hotpoint Refrigerator Caps and Lids
- Hotpoint Refrigerator Grilles and Kickplates
- Hotpoint Refrigerator Knobs
- Hotpoint Refrigerator Brackets and Flanges
Popular Hotpoint Refrigerator Models
Below are the most popular Hotpoint Refrigerator models we have. Enter your model number in the search box to find your model.
- HTS18GBSARWW Top Freezer S Series
- HSS25GFPJWW Side-by-side P Series
- HSM25GFTASA Side-by-side T Series
- HSS25GFTAWW Side-by-side T Series
- HSM25GFRFSA Side-by-side R Series
- HSS25GFPAWW Side-by-side P Series
- HTS17GBSERWW Top Freezer S Series
- HSS25IFMDWW Side-by-side M Series
- HSS25GFPHWW Side-by-side P Series
- HSM25GFRESA Side-by-side R Series
- HSS25GFTABB Side-by-side T Series
- HTS17GBSARWW Top Freezer S Series
- HSM25GFRASA Side-by-side R Series
- HSS25GFPDWW Side-by-side P Series
- HTS22GBPBRWW Top Freezer P Series
- HTS15BBMFRWW Top Freezer M Series
- HSM25GFTCSA Side-by-side T Series
- HTS16GBRFRWW Top Freezer R Series
- HSH25GFBBBB
- HTS15BBMBRWW Top Freezer M Series
