Husqvarna Chainsaw Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Husqvarna Chainsaw Parts
- Engine stops after a few seconds or minutes
- Will Not Start
- See more...
- Engine stops after a few seconds or minutes
- Will Not Start
- See more...
- Will Not Start
- See more...
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Husqvarna Chainsaw Appliance Types
Related Husqvarna Chainsaw Parts
- Husqvarna Chainsaw Bearings
- Husqvarna Chainsaw Belts
- Husqvarna Chainsaw Brackets and Flanges
- Husqvarna Chainsaw Brushes
- Husqvarna Chainsaw Caps and Lids
- Husqvarna Chainsaw Carburetors
- Husqvarna Chainsaw Deflectors and Chutes
- Husqvarna Chainsaw Engines
- Husqvarna Chainsaw Exhausts
- Husqvarna Chainsaw Filters
- Husqvarna Chainsaw Gears
- Husqvarna Chainsaw Handles
- Husqvarna Chainsaw Hardware
- Husqvarna Chainsaw Hoses and Tubes
- Husqvarna Chainsaw Knobs
- Husqvarna Chainsaw Motors
- Husqvarna Chainsaw Pulleys
- Husqvarna Chainsaw Pumps
- Husqvarna Chainsaw Seals and Gaskets
- Husqvarna Chainsaw Spark Plugs
- Husqvarna Chainsaw Springs and Shock Absorbers
- Husqvarna Chainsaw Starters
- Husqvarna Chainsaw Switches
- Husqvarna Chainsaw Tanks and Containers
- Husqvarna Chainsaw Thermostats
- Husqvarna Chainsaw Transmissions and Clutches
- Husqvarna Chainsaw Valves
- Husqvarna Chainsaw Wheels and Rollers
- Husqvarna Chainsaw Wire Plugs and Connectors
Popular Husqvarna Chainsaw Models
Below are the most popular Husqvarna Chainsaw models we have. Enter your model number in the search box to find your model.
- P3314 Chain Saw
- P3314 Wsa Chain Saw
- 2375 Le Chain Saw
- 2375 Le Chain Saw
- 450 Chainsaw
- 450 450
- 450 450 (20103600001-20113600000)
- 450 Chainsaw
- 450 450 (2007-03)
- 450 450 (2009-02)
- 450 450, 450ii, 450e, 450eii, 450 Rancher, 450 Rancherii - 450ii (450 Rancherii)
- 2150 Pr Chain Saw
- 2150 Pr Chain Saw
- 2150 Le, Predator Le
- 2150 Pr Chain Saw
- 2150 Pr Chain Saw
- 2150 Pr Chain Saw
- 2150 Le, Predator Le
- 2150 Pr Chain Saw
- 142E Chainsaw