Husqvarna Edger Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Husqvarna Edger Parts
- Engine stops after a few seconds or minutes
- Will Not Start
- See more...
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Husqvarna Edger Appliance Types
Related Husqvarna Edger Parts
- Husqvarna Edger Bearings
- Husqvarna Edger Blades
- Husqvarna Edger Brackets and Flanges
- Husqvarna Edger Caps and Lids
- Husqvarna Edger Carburetors
- Husqvarna Edger Control Cables
- Husqvarna Edger Engines
- Husqvarna Edger Exhausts
- Husqvarna Edger Filters
- Husqvarna Edger Gears
- Husqvarna Edger Handles
- Husqvarna Edger Hardware
- Husqvarna Edger Hoses and Tubes
- Husqvarna Edger Ignitions
- Husqvarna Edger Knobs
- Husqvarna Edger Manuals and Literature
- Husqvarna Edger Panels
- Husqvarna Edger Seals and Gaskets
- Husqvarna Edger Springs and Shock Absorbers
- Husqvarna Edger Starters
- Husqvarna Edger Switches
- Husqvarna Edger Tanks and Containers
- Husqvarna Edger Transmissions and Clutches
- Husqvarna Edger Wheels and Rollers
- Husqvarna Edger Wire Plugs and Connectors
Popular Husqvarna Edger Models
Below are the most popular Husqvarna Edger models we have. Enter your model number in the search box to find your model.
- 128LD 128 Ld - 20093100001-Current (Us_can)
- 128LD 128 Ld - 952711953 (Us_lowes)
- 128LD 128 Ld - 952711969 (Us_can)
- 128CD 128 Cd - 952711952 (Us Only)
- 128CD 128 Cd - 952711968 (Us_can)
- 224L 224 L
- 123L 123 L
- 322L 322 L (20000100001-20020100000)
- 322L 322 L (20020100001-20150100000)
- 322L 322 L (19991000001-20000100000)
- 323L 323 L (20041000001-20051800000)
- 323L 323 L (20061400001-20070100000)
- 323L 323 L (20020100001-20041000000)
- 323L 323 L (20080900001-Current)
- 323L 323 L (20051800001-20061400000)
- 323L 323 L (20070100001-20080900000)
- 325LX 325 Lx (20051800001-20080900000)
- 325LX 325 Lx (20000100001-20020100000)
- 325LX 325 Lx (20080900001-Current)
- 325LX 325 Lx (19991000001-20000100000)