Maytag Garbage Disposer Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Maytag Garbage Disposer Parts
Your Price
$11.10
In Stock
Maytag Garbage Disposer Hose Clamp
PartSelect Number PS11740613
Manufacturer Part Number WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Stephen from Laveen, AZ
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.
Read more...
Your Price
$9.81
In Stock
Maytag Garbage Disposer Hose Clamp
My husband took apart the bottom panel and showed me what the part looked like and I was able to find it on your website. I was able to order the parts and have my husband repair the washer so I was only without a washer for a week and a half. Thank you. Read more...
PartSelect Number PS11743289
Manufacturer Part Number WP616099
Note: This part has been updated by the manufacturer. It may appear different but will still function the same as the original. The hose clamp is about 2 inches in diameter and made of stainless steel. A hose clamp generally attaches hoses and tubes to various equipment This part consists of a band and a screw that tightens along the slots when it is turned. This part works with washers, dishwashers, food waste disposers, and ice makers. This will need to be replaced if you notice leaking coming from the appliance.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Tina from Denver, PA
A wirre from an underwire bra punctured a hole in tub to pump hose. Water leaked out all over the floor.
I searched the internet for parts because we had just had a repairman out to fix the knocking noise in the washer drum. He found an underwire from a bra there and removed it. That cost about $100. My husband took apart the bottom panel and showed me what the part looked like and I was able to find it on your website. I was able to order the parts and have my husband repair the washer so I was only without a washer for a week and a half. Thank you. Read more...
Your Price
$32.72
In Stock
Maytag Garbage Disposer Splash Guard
PartSelect Number PS11742344
Manufacturer Part Number WP4211334
The splash guard, also known as a mounting gasket, is used for garbage disposals. The splash guard creates a watertight seal between the sink flange and the garbage disposal ring. The rubber cover covers the top of the sink drain and it opens in the center to allow water and food particles into the garbage disposal while keeping liquids and food from splashing out or back into the sink. This should fix any issue or symptom of garbage coming back out of your sink. Refer to the manufacturer-approved instructional diagram for installation and accurate guidance.
Fixes these symptoms
- Garbage comes back up sink
- Smells bad
- See more...
Installation Instructions
Richard from CENTERVILLE, UT
Worn out splash guard
Ask my grandson to replace it. He’s a genius. He used hammer to release the disposer circular latch. He then removed the old splash guard and installed the new one. Love him
Read more...
Your Price
$21.90
Special Order
Your Price
$17.93
Special Order
Maytag Garbage Disposer Hardware Installation Kit
PartSelect Number PS2371817
Manufacturer Part Number 8174355A
This hardware installation kit may also be known as a garbage disposal installation kit, and is used in conjunction with your garbage disposal. This hardware kit contains all five of the parts you will need in order to install your appliance. Using the instructions in the garbage dispoal manual, and the pieces included in this assembly, you can install your appliance with ease. For more information on what pieces are included in the kit please see the image provided. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- See more...
Maytag Garbage Disposer Appliance Types
Popular Maytag Garbage Disposer Models
Below are the most popular Maytag Garbage Disposer models we have. Enter your model number in the search box to find your model.
