Roper Cooktop Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Roper Cooktop Parts
Your Price
$6.96
In Stock
Roper Cooktop Drip Bowl - 6 Inch
. Read more...
PartSelect Number PS11750108
Manufacturer Part Number WPW10196406
This drip bowl is used for electric cooktops and ranges, it is designed to sit under a 6-inch surface burner. It catches the drips and spills coming from the cookware on the surface burner. This drip bowl is chrome, and it has a diameter of 8 inches. You need to remove the burner element to replace this part. Line the hole up with the element terminal blocks, and ensure the new bowl is flush with the surface of the cooktop before replacing the burner element. Drip bowls need to be replaced when they are lost, damaged, or you are no longer able to clean them adequately. This replacement part is sold individually.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Joe from Greeley, CO
oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then removed element and replaced with new. Read more...
Your Price
$10.88
In Stock
Roper Cooktop Drip Bowl - 8 Inch
PartSelect Number PS2366563
Manufacturer Part Number W10196405RW
This part is located beneath the element and catches any spills.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Michael from Kings Park, NY
Drip bowls were rusty and rotting through
I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better!
Read more...
Your Price
$13.42
In Stock
Roper Cooktop Surface Burner Plug-In Block Kit
I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon Read more...
PartSelect Number PS340571
Manufacturer Part Number 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to the inner wiring of your appliance. Without this connection your burner element would not get the electrical current it needs to heat up. When your element will not heat at all, or if it is not heating properly it is likely an issue with the terminal block. You need to remove the element to replace this part. While you have the element out, inspect the element and the terminal for any corrosion, arcing, or discoloration. If you notice any damage to the element or the terminals we recommend you replace this part as well. This kit includes two metal brackets, two pre-crimped high-temperature wire leads, two ceramic wire nuts, two heat-shrinking insulators, and a mounting screw. Before you begin this repair, make sure you have unplugged your appliance.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Jon from Oakley, CA
Surface elements quit working
Drilled out old and broken hold down clips, installed new ones(4). Cut old wires attached to surface plug in block, striped wires, and attached new plugin kit(4), warmed up heat shrink with a hair dryer, put in new drip bowels, the stove is like new.I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly.
Way to go Part Select.com
Jon Read more...
Your Price
$53.00
In Stock
Roper Cooktop Heating Element
PartSelect Number PS11742505
Manufacturer Part Number WP4391960
This element carries 5200W and 240V.
Note: This element no longer includes two terminals and two adapter leads. They must be ordered separately.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Bill from Morristown, TN
Dryer quit heating. Suspected heating element was open
Unplugged the 220 volt source. Disconnected the vent line from the back of the drier. Removed the six screws holding the back panel with a 1/4 inch nut driver. Tipped the drier up at a 45 degree angle against the wall to give better access to the inside. Removed the screws holding the two thermostats to the side of the heater box and laid them aside. Disconnected the two red power lines to the heater element. Removed the large screw at the top of the heater box and removed the flexible bracket holding the heater box, then lifted the heater box up and away from the drier. Removed the one screw holding the heater element inside the heater box and pulled out the old heating element. The old element was open as found using an ohmeter on the two main terminals. Threw away the old element. Removed the new heating element from the box and slid it into the heater box making sure to align the terminal bracket with the hole in the heater box for the reinstallation of the mounting screw. Tightened this screw. Remounted the heater box to the two mounting slots and reinstalled the flexible mounting bracket to the top of the heater box and installed and tightened the large screw holding this bracket. Cut off and removed the old electrical push-on terminals from the two red power wires for the heater element. These were discolored and oxidated from the conducted heat over the years of operation. Using the supplied short red leads with push-on terminals already installed, I wire tied these new leads to the existing red power leads and pushed them onto the heater element terminals. Rechecked the soundness of the twisted wire connections to make sure they were tight. Replaced the back panel and reinstalled the six 1/4" screws with the 1/4' nut driever. Reinstalled the driver vent line and tightened its holding ring. Slid the drier back into position on the floor. Checked the level and readjusted the leveling legs for a steady floor stance. Reinstalled the 220 volt power connecter and set the controlls for a drying cycle. Let the drier run for aproximately 1 minute and then checked the air temperature inside the drier. IT WAS NOW PRODUCING HOT AIR. Project completed successfully and I was now a HERO in my wifes eyes. Absolutely no technical problems encountered. Just remember, unplug the drier before starting ANY repairs. To forget this COULD RUIN YOUR DAY.
Read more...
Your Price
$50.86
In Stock
Roper Cooktop Delta Frame Surface Unit - 6 Inch
PartSelect Number PS11757480
Manufacturer Part Number WPY04100165
This is a delta frame surface unit, also known as coil element, for a stove, range, or oven. It is a 6-inch surface burner with a reinforced delta frame that carries 1250 watts and 240 volts. The burner has four turns and is compatible with many electric ranges. The center medallion is black in color. The burner provides heat to your cooking area to cook your food items. If your burner is not heating properly, you may need to replace it. Be sure to disconnect power to the appliance before completing this repair.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
ron from WALNUT CREEK, CA
Element has reached its life expectancy.
The new element has a manufacturing defect. This problem was immediately rectified by their salesperson Mary. Another burner element is on its way thanks to the professional and personal help from Mary.
Read more...
Your Price
$124.97
In Stock
Roper Cooktop Burner Surface Element - 8 Inch
PartSelect Number PS11740818
Manufacturer Part Number WP3177565
This is a burner surface element and is 8 inches in diameter and 2600 watts. The burner surface element functions as a cooking area on the cooktop of the range. The purpose of this part is to supply heat to the cooking area. This is a 5 turn coiled surafce element that features looped terminal ends. The element is sold individually. Before installing, make sure to unplug the cooktop and to allow enough time for your current element to cool down. The most common reason for needing a new element is if your current one will not heat.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Donna from Charlotte, NC
Cooktop was looking old and worn though there was no working problem.
All of the "old" pieces were very easily removed and replaced with the new pieces. The update looks terrific and works just fine!
Read more...
Your Price
$54.57
In Stock
Roper Cooktop Igniter Switch
PartSelect Number PS11742372
Manufacturer Part Number WP4330739
This is an igniter switch for a gas oven, stove, or range. This part is sold individually. When the gas burner valve knob is pressed and rotated, the igniter switch creates a spark that ignites the gas and starts the burner. Without this switch, the burner cannot ignite. This part is approximately 1.5 inches tall and wide. It is made of plastic, and is white in color. This part is sourced directly from the original manufacturer. Be sure to disconnect power to your oven before completing this repair.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$69.15
In Stock
Roper Cooktop Appliance Types
Popular Roper Cooktop Models
Below are the most popular Roper Cooktop models we have. Enter your model number in the search box to find your model.
