Samsung Dryer Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Samsung Dryer Parts
Your Price
$41.80
In Stock
Samsung Dryer Drum Support Roller & Axle
PartSelect Number PS4221885
Manufacturer Part Number DC97-16782A
The drum support roller and axle, which includes the roller shaft and mounting clips, is used in dryers. This part holds the drum as it rotates on the support wheels. When the roller begins to wear out, it self lubricates, so no additional grease is needed. If your dryer is making odd noises then checking and replacing the rollers can be the solution to your problem. Make sure to unplug the dryer from the power source before beginning this replacement. Refer to the diagram and installation instructions provided by manufacturer.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Tad from MINOT AFB, ND
Loud noise like boots being ran through the dryer
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in the front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
Read more...
Your Price
$47.91
In Stock
Samsung Dryer Radiant Flame Sensor
2. Removed two bolts at bottom front of machine and took off the bottom front panel.
3. Removed three bolts from black plastic exit vent and took it out to give more room to access everything.
4. removed two wires and screws on the limit thermostat. Did the reverse to place the new one.
5. Removed wires (remembering placement), then holder screw. rotated the Gas Dryer Sensor counter clockwise to release the bottom tab so the sensor can be taken off the flame tube. Did the reverse to place the new one on.
6. Removed the one screw on the gas/flame tube that holds the bracket and igniter inside the flame tube. Removed the wires fro the igniter (remember placement) Slid the whole assembly toward the back of the machine to get the tube off the gas valve then rotated the whole assembly counter-clocwise to release the tab on the left side of the bracket. This was a little tight and had to work with it a bit to get the tab out and slide the whole piece out of the flame tube.
7. Once the tube and igniter were out i removed the scree that holds the igniter and replaced with the new one. Made sure no dust, etc. was in the piece.
8. Did the reverse to place the tube/igniter back into the flame tube.
9. Carefully and forcefully removed the wire connectors to the two coils. These were tough to get off. Removed the two screws that hold the bracket that holds the two coils in place. Slid the coils off the spindles remembering which one has the two wire connection and which one has the three wire connection and the way they went on. Replaced the old with the new. Placed the bracket onto the new coils and made sure the little bumps on the top are in the holes in the bracket. Tightened the screws to hold the coil bracket. Reattached the wire connectors to the coils making sure they go ALL the way back on.
10. Vaccumed everything I could to get lint, dust, etc. out.
11.Replaced the black vent plastic.
12 Made sure the exit vent on the back was not crimped or clogged. Checked the little flap door where the vent goes outside to make sure it opens and closes super easy to no air flow is restricted.
13. For testing I left the bottom panel open. Make sure you closed the door, reconnect the plug and turn the gas valve back on. Hit the go button on autodry or timed dry. The door must be closed to create the closed circulation of the system so the fan sucks the flame into the tube otherwise the flame will not fire deep into the tube and will set off one fo the overheat sensors. After hitting the go button your drum will start to rotate, then a few seconds later you'll hear a click and your igniter will start to burn bright orange. Another click and the gas should flow and ignite.
14. This shows that you've fixed the ignition problem. I just replaced everything I thought that could be wrong in stead of hunting and trial and error. All the parts were about $137 so I thought it was worth making sure.
15. IMPORTANT: If during your test the flame turns off after a little while then turns back on only to turn off again, don't panic. This happened to me as well. I found that you need to run the dryer with wet clothes in the dryer. The wetness in the clothes will keep the autodry sensor from shutting off the dryer since there will be moisture in the exhaust. If it's on timed dry the wet clothes will cool the exhaust air and keep the overheat sensors from turning the heat off. So no heating of dry clothes to get out wrinkles. Just dry the wet clothes. This is all I did and it's been working great so far. Good Luck! Read more...
PartSelect Number PS11741429
Manufacturer Part Number WP338906
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough to ignite gas to light the burner. Once the igniter is hot enough it will open the valve and allow gas to flow. This is a safety mechanism to prevent dangerous levels of gas from building up. To repair, the main top of the dryer should be lifted, as well as the front panel to access the component. This flame sensor assembly is made of both plastic and metal.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Michael from Kirkwood, MO
Gas Dryer would not ignite
1. Removed lint screen and holder frame. Unplugged the electrical cord and closed the gas valve in the line before it goes into the dryer.2. Removed two bolts at bottom front of machine and took off the bottom front panel.
3. Removed three bolts from black plastic exit vent and took it out to give more room to access everything.
4. removed two wires and screws on the limit thermostat. Did the reverse to place the new one.
5. Removed wires (remembering placement), then holder screw. rotated the Gas Dryer Sensor counter clockwise to release the bottom tab so the sensor can be taken off the flame tube. Did the reverse to place the new one on.
6. Removed the one screw on the gas/flame tube that holds the bracket and igniter inside the flame tube. Removed the wires fro the igniter (remember placement) Slid the whole assembly toward the back of the machine to get the tube off the gas valve then rotated the whole assembly counter-clocwise to release the tab on the left side of the bracket. This was a little tight and had to work with it a bit to get the tab out and slide the whole piece out of the flame tube.
7. Once the tube and igniter were out i removed the scree that holds the igniter and replaced with the new one. Made sure no dust, etc. was in the piece.
8. Did the reverse to place the tube/igniter back into the flame tube.
9. Carefully and forcefully removed the wire connectors to the two coils. These were tough to get off. Removed the two screws that hold the bracket that holds the two coils in place. Slid the coils off the spindles remembering which one has the two wire connection and which one has the three wire connection and the way they went on. Replaced the old with the new. Placed the bracket onto the new coils and made sure the little bumps on the top are in the holes in the bracket. Tightened the screws to hold the coil bracket. Reattached the wire connectors to the coils making sure they go ALL the way back on.
10. Vaccumed everything I could to get lint, dust, etc. out.
11.Replaced the black vent plastic.
12 Made sure the exit vent on the back was not crimped or clogged. Checked the little flap door where the vent goes outside to make sure it opens and closes super easy to no air flow is restricted.
13. For testing I left the bottom panel open. Make sure you closed the door, reconnect the plug and turn the gas valve back on. Hit the go button on autodry or timed dry. The door must be closed to create the closed circulation of the system so the fan sucks the flame into the tube otherwise the flame will not fire deep into the tube and will set off one fo the overheat sensors. After hitting the go button your drum will start to rotate, then a few seconds later you'll hear a click and your igniter will start to burn bright orange. Another click and the gas should flow and ignite.
14. This shows that you've fixed the ignition problem. I just replaced everything I thought that could be wrong in stead of hunting and trial and error. All the parts were about $137 so I thought it was worth making sure.
15. IMPORTANT: If during your test the flame turns off after a little while then turns back on only to turn off again, don't panic. This happened to me as well. I found that you need to run the dryer with wet clothes in the dryer. The wetness in the clothes will keep the autodry sensor from shutting off the dryer since there will be moisture in the exhaust. If it's on timed dry the wet clothes will cool the exhaust air and keep the overheat sensors from turning the heat off. So no heating of dry clothes to get out wrinkles. Just dry the wet clothes. This is all I did and it's been working great so far. Good Luck! Read more...
Your Price
$44.87
In Stock
Samsung Dryer Drive Belt
PartSelect Number PS4133825
Manufacturer Part Number 6602-001655
The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This goes between the drive motor and the dryer drum. The belt may have broken, which will cause the drum to not turn properly. You will need to pull your dryer away from the wall and use your Phillips screwdriver to remove the screws on the back. This is an OEM product, shipped directly from the manufacturer.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Christopher from SUGARLOAF, CA
The dryer turned on but the drum did not move when you pressed start even though It started it cycles.
I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you
Read more...
Your Price
$153.11
In Stock
Samsung Dryer Heating Element - 5300W
PartSelect Number PS4205218
Manufacturer Part Number DC47-00019A
This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Cynthia from JOHNSTOWN, NY
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Read more...
Your Price
$62.67
In Stock
Samsung Dryer Idler Pulley Assembly
PartSelect Number PS11771601
Manufacturer Part Number DC93-00634A
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the dryer belt, allowing it to rotate the drum during the drying cycle. Over time, the pulley wheel and its bearings can wear out leading to squeaking and grinding noises when the drum rotates. The bracket or pulley wheel can also fall out of alignment which can damage the belt and cause it to slip off. Eventually, a faulty idler pulley assembly will prevent the drum from rotating altogether. Depending on your dryer model, you may need to disassemble the dryer to access the pulley assembly. Remove the dryer belt from the idler pulley wheel and detach the assembly from the dryer frame. Position the new assembly in its place and secure it in position. Thread the belt over the pulley and around the dryer drum, ensuring that the grooved side lays flat against the drum. Manually spin the drum to check that the belt is properly tensioned and reassemble your appliance.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Vicky from BLOOMSBURY, NJ
Belt fell off because of belt roller on the tensioner melted, ciezed and fell off
Watched a video on utube, how to repair my 16 month old steam dryer. The hardest part was laying on my belly holding the spring loaded tensioner and slipping the belt on around the blower housing. Only cost me $23. Winning!
Read more...
Your Price
$16.32
In Stock
Samsung Dryer Light Bulb - 10W
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.
Edward Brennan Read more...
PartSelect Number PS11739347
Manufacturer Part Number WP22002263
This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.
Installation Instructions
Edward from Andover, NJ
Dryer was sqeaking loudly when running
I Looked on internet sites for this type of problem.Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.
Edward Brennan Read more...
Your Price
$35.53
In Stock
Samsung Dryer Thermistor
PartSelect Number PS4204984
Manufacturer Part Number DC32-00007A
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of needing a new thermistor is the dryer cycle not working. Before installing this part, you should disconnect your dryer from its power source. We also recommend you wear work gloves to protect your hands during this installation. To make this repair, the tools you will need include a multi-screwdriver, a Phillips head bit, and a flat-head bit.
Installation Instructions
Cynthia from JOHNSTOWN, NY
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Read more...
Your Price
$25.28
In Stock
Samsung Dryer Thermal Fuse
PartSelect Number PS4205213
Manufacturer Part Number DC47-00016A
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying cycle. A faulty thermostat could result in clothes getting burned because the heating element does not receive the necessary signal to stop producing heat. This is a dangerous situation and could also lead to a fire. Ensure that you disconnect the power source to your dryer before you conduct this repair. This thermostat is connected to the clothes dryer unit by two screws which are sold separately.
Installation Instructions
Cynthia from JOHNSTOWN, NY
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Read more...
Your Price
$288.42
In Stock
Samsung Dryer Assembly DUCT HEATER;27-DRYE
PartSelect Number PS4220205
Manufacturer Part Number DC97-14486A
This genuine OEM heater duct assembly in your dryer directs hot air into the drum during operation. Generally, it can be found behind the drum or at the rear of the dryer. If this assembly becomes damaged, you may encounter problems such as clothes not drying properly or drying unevenly. This kit includes the housing with the heating element coil and attached insulators.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Mark from WEST SUNBURY, PA
Dryer stopped heating
I purchased wholesale heater element with sensors. Couple wires and bolts to attach. Trickiest part is disassembling the dryer to remove the old heating unit. You-tube it; it's gold.
Read more...
Your Price
$112.09
In Stock
Samsung Dryer CASE-FILTER;GRACE-DRYER,
PartSelect Number PS4206799
Manufacturer Part Number DC61-02595A
This lint filter case, also known as a lint filter screen case, helps to trap lint and debris from laundry and prevent it from clogging your dryer vent. It is specially designed for Samsung dryers. The lint filter case includes mesh fabric in a plastic casing. It has a length of 12 inches, and a width of 8.75 inches. If the lint filter case is visibly damaged, it will need to be replaced to keep your dryer running efficiently. Other signs of a faulty lint filter case include your clothes not drying as quickly as usual, an unpleasant odor in the dryer, and an increased amount of lint on your clothes.
Samsung Dryer Appliance Types
Popular Samsung Dryer Models
Below are the most popular Samsung Dryer models we have. Enter your model number in the search box to find your model.
- DV42H5000EW Dryer
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW DRYER
- DV42H5000EW Samsung Dv42h5000ew/A3-02 Dryer
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW Samsung Dv42h5000ew/A3-03 Dryer
- DV42H5000EW DRYER
- DV42H5000EW DRYER
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer
- DV42H5000EW Samsung Dv42h5000ew/A3-01 Dryer
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW Samsung Dv42h5000ew/A3-00 Dryer
- DV42H5000EW DRYER
- DV45H7000EW DRYER
- DV45H7000EW 7.4 Cu. Ft. 9-Cycle Electric Dryer - White
- DV45H7000EW Samsung Dv45h7000ew/A2-01 Dryer
- DV45H7000EW Samsung Dv45h7000ew/A2-02 Dryer
- DV45H7000EW Samsung Dv45h7000ew/A2-00 Dryer
- DV45H7000EW 7.4 Cu. Ft. 9-Cycle Electric Dryer - White
