Official Samsung Wall Oven Parts

Videos!

Range Oven Temperature Sensor – Part Number: DG32-00002B

Your Price

$130.08

Samsung Stove Range Oven Temperature Sensor

★★★★★

6 Reviews

PartSelect Number PS4240743

Manufacturer Part Number DG32-00002B

This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor features a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.

Fixes these symptoms

Little to no heat when baking
See more...

Installation Instructions

Steven from CHEYENNE, WY

Oven would not heat consistently

My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG! Read more...

Videos!

Dual Element Switch – Part Number: DG44-01002A

Your Price

$154.13

Samsung Stove Dual Element Switch

★★★★★

10 Reviews

PartSelect Number PS4240803

Manufacturer Part Number DG44-01002A

This is a dual element switch that is made for use within Samsung ranges. This switch is necessary to turn the heating elements on and off, and control how hot they get. Over time and with more frequent use, this element switch can fail, however, it can also break if it is damaged by a power surge or food contamination. To replace this switch, you will need a screwdriver to access it and a set of pliers to remove the wires connected to it. This switch is sold individually, so be sure to check how many switches are not working properly before ordering.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Jeffrey from Hooksett, NH

Dual burner only operates on high, no matter the setting

Followed video at the link below.

https://www.bing.com/videos/search?q=how+to+replace+infinity+switch+in+samsung+electric+range&docid=607999620772294704&mid=702E9DF006DF9B180DAA702E9DF006DF9B180DAA&view=detail&FORM=VIRE Read more...

Oven Burner Igniter – Part Number: DG94-00520A

Your Price

$218.00

Samsung Stove Oven Burner Igniter

★★★★★

12 Reviews

PartSelect Number PS4241428

Manufacturer Part Number DG94-00520A

This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent use or food contamination, this burner can fail and will need to be replaced. If your burner is glowing red or orange, it is functioning as intended, but if your oven does not heat up properly, it likely needs replacement. This oven burner igniter is an OEM part that comes by itself and does not come with any of the screws necessary to secure it inside your oven.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

John from EAST QUOGUE, NY

Oven not heating and holding temp

The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the center of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes. Read more...

Micro Door Switch – Part Number: 3405-001034

Your Price

$37.08

Samsung Stove Micro Door Switch

★★★★★

10 Reviews

PartSelect Number PS4131192

Manufacturer Part Number 3405-001034

This door switch, also known as a safety switch, is a genuine OEM replacement part for microwaves. It is a safety mechanism that sends signals to the microwaves control system, telling it when the door is open/closed. This ensures that the microwave only operates when the door is securely shut and switches off as soon as the door is open. Over time, this switch can become worn out or damaged. A faulty door switch can result in failure to switch the microwave on/off, lack of heat, and running with the door open. To confirm that the door switch is faulty, use a multimeter to test for electrical failure. To remove the faulty switch, disconnect the wiring connectors and take note of where they are positioned. Place the new switch in position and reattach the wiring connectors to the appropriate terminals and close the microwave door to check that the switch engages appropriately.

Fixes these symptoms

Doesn’t shut off
No heat
Won’t turn on
See more...

Installation Instructions

Lynn from LOUISVILLE, KY

Microwave would not start when door closed. Sometimes you could push in or jiggle door and it would work for awhile and then it woud stop again. I knew it eas a door switch issue but wasn't certain which of the 3 or the body latch itself.

I removed the body latch assembly and found the bottom micro switch (NC) terminal burnt and loose. I replaced and working perfectly fine now. Easy diagnose and easy repair. Read more...

Your Price

$84.34

Samsung Stove Knob

★★★★★

6 Reviews

PartSelect Number PS9606608

Manufacturer Part Number DG64-00473A

This stainless steel knob dial on your range allows you to control the temperature and function of your range. It is found on the front panel. If it is difficult or impossible to adjust the heat settings, it is time to replace your knob dial. It can easily be pulled off and popped into place. Since this genuine OEM dial is sold individually, check how many you need before getting a replacement.

Installation Instructions

Grace from BETHEL, CT

Oven igniter burned out needed to replace

With a screwdriver Read more...

Your Price

$28.98

Samsung Stove Thermostat

★★★★★

4 Reviews

PartSelect Number PS4226434

Manufacturer Part Number DE47-20037A

This is a high limit thermostat designed for microwaves, ranges and ovens. Made of plastic and metal, this thermostat is designed to open the electrical circuit for your appliance when it reaches a specific internal temperature. In some cases, high limit thermostats can become defective and if your appliance will not turn on, or has a specific error code, it must be replaced. This thermostat is a genuine OEM part that is sold as an individual part and can be replaced by disconnecting the appliance from the power, and accessing its panel, usually located near the bottom of your range, or wherever the heating element is located. Reference your user manual for exact location and replacement instructions.

Fixes these symptoms

Door won’t open after self cleaning cycle
See more...

Installation Instructions

Uwe from FORT COLLINS, CO

Oven shut off during self clean cycle and door stayed locked.

I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11. Read more...

Triple Burner Switch – Part Number: DG44-01007B

Your Price

$184.60

Samsung Stove Triple Burner Switch

★★★★★

5 Reviews

PartSelect Number PS11735755

Manufacturer Part Number DG44-01007B

This surface element triple burner infinite switch, or regulator control, is located in the control panel of your range oven. It is responsible for turning the surface element on or off and adjusting its heat. If this switch or regulator is broken, you might notice the burner heating uncontrollably or not heating at all. Please remember that genuine OEM replacement part is designed for triple burners. Your range model may use various types of switches, so be sure to choose the correct one when making your purchase.

Installation Instructions

Jimmie D. from THOMPSON, MO

The triple burner switch would only stay on the highest setting.

I removed the control panel with a Phillips screwdriver and unplugged the burner switch and replaced the new switch and put the control panel back in place and turned on the burner and it worked as it should.i realized that I only would have only had to remove the 4 screws on the bottom of the control panel. All I would have had to do was just take those 4 screws out and remove the switch control knob and the two screws that held the switch in. Am very happy with the results Read more...

Right Rear Burner Cap - Black – Part Number: DG62-00111A

Your Price

$63.20

Samsung Stove Right Rear Burner Cap - Black

★★★★★

2 Reviews

PartSelect Number PS5576950

Manufacturer Part Number DG62-00111A

This surface burner cap is specially designed to fit with Samsung ranges. It is a genuine OEM replacement part supplied directly by Samsung to ensure compatibility. The burner cap is a round, black cap that has a diameter of approximately 1.75 inches. It covers the burner head and helps to distribute the flame across the burner to ensure your food is cooked evenly. The cap also protects the burner head from accidental food spillage and debris to keep your range running efficiently. The burner cap will need to be replaced if it is cracked or can no longer remain securely attached to the burner head. Each cap is sold individually.