Snapper Generator Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Snapper Generator Parts
Your Price
$45.30
In Stock
Snapper Generator Cap, Fuel Gauge
PartSelect Number PS9314364
Manufacturer Part Number B4363GS
This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It is approximately 5.25 inches in length, while the head has a diameter of 3 inches. The purpose of the cap is to cover and protect the fuel gauge, which indicates the levels of gas available in the tank. It prevents dirt and debris from entering the gauge area and prevents fuel from leaking out. A faulty cap will allow contaminants to enter the gauge, and cause fuel to leak, leading to inaccurate fuel readings and safety risks. Twist the cap to remove it and clean the surrounding area thoroughly. Place the new gauge cap in position and ensure that it is locked in place.
Your Price
$5.19
In Stock
Your Price
$19.31
In Stock
Snapper Generator Fuel Valve W/Bushing
PartSelect Number PS8911051
Manufacturer Part Number 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor.
This part is found on the underside of the fuel tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair.
Customers rate this repair as Easy.
Fixes these symptoms
- Will Not Start
- See more...
Your Price
$37.96
In Stock
Snapper Generator Battery Charger
PartSelect Number PS12089850
Manufacturer Part Number 705927
Installation Instructions
James from PICAYUNE, MS
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Read more...
Your Price
$59.96
In Stock
Your Price
$9.58
In Stock
Your Price
$149.91
In Stock
Your Price
$12.38
In Stock
Your Price
$25.16
In Stock
Snapper Generator Assembly, Holder, Brush
PartSelect Number PS9063496
Manufacturer Part Number 66386GS
The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is broken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.
Your Price
$107.95
In Stock
Snapper Generator Regulator-AVR Control
PartSelect Number PS9270265
Manufacturer Part Number 205858GS
The OEM voltage regulator or voltage control is a part used to regulate the voltage so it can provide the right amount of power to electrical components. It attaches inside the alternator housing. The part is black and 2 x 3.5 inches. If damaged, the voltage will become too low/high and the part should be replaced. This part requires a voltmeter to use properly. Please refer to your make, model, and diagram to ensure this is the correct part.
Snapper Generator Appliance Types
Related Snapper Generator Parts
- Snapper Generator Bearings
- Snapper Generator Caps and Lids
- Snapper Generator Exhausts
- Snapper Generator Hardware
- Snapper Generator Hoses and Tubes
- Snapper Generator Seals and Gaskets
- Snapper Generator Wheels and Rollers
- Snapper Generator Wire Plugs and Connectors
Popular Snapper Generator Models
Below are the most popular Snapper Generator models we have. Enter your model number in the search box to find your model.
- 030834-01 030834-01 - 6,500 Watt Snapper 49 State
- 1667-0 1667-0 - 3,250 Watt Snapper
- 030834-00 030834-00 - 6,500 Watt Snapper 49 State
- 6517-00 Infohub
- 1666-1 1666-1 - 1,000 Watt Snapper
- 7084745 Snapper Generator Model 7084745 Parts
- 030216-1 030216-1 - 6,200 Watt Snapper
- 7085906 Snapper Generator Model 7085906 Parts
- 030216 Generator
- 030215 Generator
- 030216-0 030216-0 - 6,200 Watt Snapper
- 030214-0 030214-0 - 3,500 Watt Snapper
- 030215-1 Generator
- 7085905 Snapper Generator Model 7085905 Parts
- 7084747 Snapper Generator Model 7084747 Parts
- 7085907 Snapper Generator Model 7085907 Parts
- 7084746 Snapper Generator Model 7084746 Parts
- 01666-1 Snapper Generator Model 01666-1 (016661, 01666 1) Parts
- 030838-00 030838-00 - 4,500 Watt Snapper Inverter Generator 49 State
- 030214 Generator
