Troy-Bilt Log Splitter Parts

Shop By Appliance Type Shop By Part Type

Popular Troy-Bilt Log Splitter Parts

Your Price

$14.31

Troy-Bilt Log Splitter Spider Bushing

PartSelect Number PS9106439

Manufacturer Part Number 735-04103

This rubber and plastic spider bushing is a genuine OEM part for various makes of log splitters and is sold as an individual part. Measuring at approximately 2-inches by 2-inches, this bushing is attached to the motor or drive shaft and is used to support the rotating shaft and other components, all while allowing smooth rotation and proper alignment. The spider bushing rides between the couplings, connecting the engine and the hydraulic pump. If you notice excessive vibrations from the motor, check the drive motor shaft for a cracked bushing or couplings, since they work together and are often replaced at the same time.

Valve, Roller Over – Part Number: 951-14075A

Your Price

$27.64

Troy-Bilt Log Splitter Valve, Roller Over

PartSelect Number PS11813571

Manufacturer Part Number 951-14075A

Your Price

$17.88

Troy-Bilt Log Splitter Coupling, .875

PartSelect Number PS9299988

Manufacturer Part Number 718-04395

Log Tray Bracket – Part Number: 753-05423

Your Price

$28.19

Troy-Bilt Log Splitter Log Tray Bracket

PartSelect Number PS9130497

Manufacturer Part Number 753-05423

Back Plate – Part Number: 781-0790A-0637

Your Price

$39.10

Troy-Bilt Log Splitter Back Plate

PartSelect Number PS9130747

Manufacturer Part Number 781-0790A-0637

This back plate, also known as a wedge plate, is sourced directly from the manufacturer for use in log splitters. It is a flat, metal plate found at the rear end of the machine, with a length of 8 inches and a width of 2 inches. It provides support and stability to the log splitter during use. The plate may fail due to excessive stress, physical damage, or corrosion. If the plate has cracks, or bends, the log splitter will become unstable and unsafe to operate. The internal components of the log splitter may also fall out of alignment and cause further damage to the equipment. Use a wrench to remove the fasteners that secure the plate to the log splitter frame. Clean the mounting area and install the new plate. Reinstall the fasteners and be careful not to overtighten them as this can damage the surface of the plate.

Your Price

$14.31

Troy-Bilt Log Splitter Coupling, .500

PartSelect Number PS9095317

Manufacturer Part Number 718-04392

This coupler connects the engine or motor to the hydraulic pump in your lawn equipment. It has a 0.5-inch inside diameter and is typically located near the rear coupling support bracket. If the coupler is broken, you will notice excessive play, cracks, or a loss of power transmission. Failure to replace a broken coupler can result in reduced power, poor operation, or complete equipment failure. To remove the coupling from your machine, remove any retaining bolts, screws, or clamps securing it in place using a wrench or socket. Afterward, gently wiggle or twist the coupling to release it. This replacement part is sourced directly from its original equipment manufacturer and is sold individually.

Your Price

$11.34

Troy-Bilt Log Splitter Hub Cap

PartSelect Number PS9301618

Manufacturer Part Number 734-0873

This OEM Hub Cap, or Dust Cap, is a 2-inch, silver, steel part, sold individually. It requires a Rubber Mallet to install and its installation is rated as Easy by our customers. This part attaches inside the wheel on the hub, and is used to keep dirt out of the hub. It must be replaced when damaged or missing (if it is damaged it will be out of round, and will not fit). Check your model number to ensure you are purchasing the correct part.

Your Price

$31.64

Troy-Bilt Log Splitter Oil Filter

★★★★★

1 Review

PartSelect Number PS9098265

Manufacturer Part Number 723-0405

The Oil Filter is a black, metal part, sold individually and certified as genuine by the original equipment manufacturer. Our customers rated this part as Easy to install. This repair requires the use of an oil filter wrench, and the oil filter connects around the pump on the frame (typically). It is used to keep oil clean and you will know if it is broken when it starts leaking, at which time it should be replaed. Check your model number to ensure you are choosing the correct part.